Trendnet TEW-805UB AC1200 Driver – Trendnet TEW-805UB AC1200 driver is a software component that allows the operating system to communicate with Trendnet TEW-805UB AC1200 Wifi Adapter. For example, suppose that an application needs to read some data from a device. The application calls a function implemented by the operating system and the operating system calls a function implemented by the controller.
If you own Trendnet TEW-805UB AC1200 Wifi Adapter and looking for drivers to connect your device to the computer, you have landed on the right site. You can download Trendnet TEW-805UB AC1200 driver here, with a simply click on the “Download Link” below.
Trendnet TEW-805UB AC1200 Driver Download
I found two immediate uses for this Wi-Fi USB flash drive. First of all, I have a Tower computer that does not have Wi-Fi, but it does not work, but to be honest, you do not move it too often and it is only a few meters away from my router. Secondly, the laptop that I upgraded to Windows 8, although it was Windows 7, the Wi-Fi connection never worked properly. Here, when I used it, I always had to be near my router and it was painful, a long Ethernet cable did not always respond to problems. Now, with this Wi-Fi, I can walk anywhere within the Wi-Fi range. How could I handle? As I said in the introduction you administer, you know that you do not have this capability and that you start / end from a point where it is not necessary / essential. But once you have it, you say how I did it. Measures 6x3x1.5cm when inserted into a USB port. It may be larger than some ports allow, so you may not be able to use the next USB port. The total length with lid on the USB memory is 8 cm and it weighs 20 grams.
The full name is AC1200 Dual Band Wireless USB Adapter TWE-805UB. It will work in both Wireless AC and Wireless N, the latter at speeds of up to 300 Mbps and the first at an incredible 867 Mbps. All this can be achieved using a USB3 port, but I have also tested it on USB2 ports and it was quite acceptable. In fact, the website says that it would work with USB 1.1, but I have not tried it. It will work with XP, Vista, Windows 7 and Windows 8, the last two 32-bit and 64-bit modes. For Windows 8 64-bit, you must download a driver from the Trendnet site for all others. The drivers and files are on a supplied CD-ROM. No doubt I managed to use it well out of reach of my normal Wi-Fi devices. The indicated figure can reach 100 meters indoors and 300 meters outdoors, but I think the modem / router must also be outside to get this last distance. There is a small and quick installation guide with eight sides, but only the first three contain the eight points needed for the configuration. There are six drop-down menus. All you need to configure is from the third menu, where you select the network you want to connect to and then enter your authentication code. Once this is done, the first menu shows the strength of the signal and the quality of the link, as well as the MAC address and other details. If you wish, you can use the last menu to configure a Wi-Fi protected configuration with a PIN or Push Button Configuration (PBC) if your router has it. Although I have not used it for large downloads, it is incredibly useful to be able to navigate along an Ethernet cable.
In most cases, the Windows drivers found here are “self-extracting” (.exe) files. Click on the desired file. When prompted, set the destination on your desk. Create a new folder and move the file to it. Click on the file to automatically extract the software and the associated files in your new folder. You can also extract or move these files to a floppy disk. Note that these files will only be self-extracting if they are run from Windows. After extracting the files to a disk or special directory, locate the installer, usually called “setup.exe” or “install.exe”, and then click on it to start the installation.
Sometimes, there is no installer because you have to install your driver through the Windows “Add a device” function. You can find instructions for installing printers in the Windows Help file. Our Mac OSX files are also self-extracting. These files must be downloaded and executed in the same way. The installer will be present on the desktop once completed: click on it and follow the instructions to install it.